I get red squiggly lines under #include "rtos.h"

I also get a red line under
SHTC3 mySHTC3;

The header is included appropriately.

Arduino IDE 2.0 does not show any error.

The code compiles and runs OK - with both Arduino IDE, and Visual Micro

The error list says the variable names are ambiguous. The rtos.h include error - says error active in severity, and cannot open source file (which it obviously does when compiling)

Any ideas?

Here is the sample code - for Portenta H7 M7 core. If you load it into Visual Studio - you should see #include rtos underlined (the include part), as well as SHTC3 references, and I2C_Mutex calls.

Thanks

Code (C++):

#include "arduino.h"
#include "mbed.h"
#include "rtos.h"
#include "ThreadDebug.h"

// Check we are using GDB Debugging and include the additional code
#ifdef VM_DEBUG_GDB
#include "ThreadDebug.h"
UsbDebugCommInterface  debugComm(&SerialUSB);
ThreadDebug            threadDebug(&debugComm, DEBUG_BREAK_IN_SETUP);
// Set to DEBUG_NO_BREAK_IN_SETUP to prevent automatic stop in setup
#endif

#include "SparkFun_SHTC3.h" // Click here to get the library: http://librarymanager/All#SparkFun_SHTC3
#include <Wire.h>
SHTC3 mySHTC3;              // Declare an instance of the SHTC3 class


using namespace mbed;
using namespace rtos;

Mutex I2C_Mutex;  // Required each time I2C bus will be used

Thread sensorThread;

const int LED_ON = LOW; // Voltage level is inverted
const int LED_OFF = HIGH;



void loop() {
  // put your main code here, to run repeatedly:
  ThisThread::sleep_for(osWaitForever);
}


void task_sensor() {
    int i = 0;
    int j = 0;

    float Temp, RH;

  // Setup I2C port
  // Will need a mutex on I2C



  for (;;) {
   
    I2C_Mutex.lock();
    mySHTC3.update();

    RH = mySHTC3.toPercent();
    Temp = mySHTC3.toDegC();

    //Read SHCT3 sensor in here
//    Serial.print("RH = ");
//    Serial.print(mySHTC3.toPercent());                        // "toPercent" returns the percent humidity as a floating point number
//    Serial.print("%, T = ");
//    Serial.print(mySHTC3.toDegC());                           // "toDegF" and "toDegC" return the temperature as a flaoting point number in deg F and deg C respectively
//    Serial.println(" deg C");





    I2C_Mutex.unlock();



    digitalWrite(LEDR, LED_ON); // Turn green LED on
    ThisThread::sleep_for(1000);
    digitalWrite(LEDR, LED_OFF); // Turn green LED off
    ThisThread::sleep_for(1000);
    ThisThread::sleep_for(10);

    i++;
    j += 2;

  }
}



void setup() {
  // put your setup code here, to run once:

  // Function for device
  //  Modbus Server (slave)
  // Web Server - show only data one way
  // Bluetooth communication with Android / iOS / .NET - for device confguration
  // Sensor Interfaces - multiple I2C sensors read by device
  //    Sensor average data =- 1 minute interval per sensor, and 60 minute interval per sensor
  // LCD panel display to display data - press any sensor and maybe will show a graph  - maybe

  //Serial.begin(115200);

  //Serial.print("Program Start\n");

  Wire.begin();

  mySHTC3.begin();

  pinMode(LEDR, OUTPUT); // Set green LED as output

  delay(5000);

  sensorThread.start(task_sensor);

} 

Thanks

I downloaded the latest version from the website (04 29 datecode), and the mbed.h and rtos.h are recognized OK, but I get other underlines with using namespace mbed etc

I will attach a screen capture to show them.

It compiles OK.

Thanks

Apologies for the delayed update on this issue, we will release an update in the coming days which should resolve these issues, and we will update this thread when it is available.

The latest release (22.04.29-2) should resolve this issue which is available from the top of the board below:
https://www.visualmicro.com/forums/YaBB.pl?board=VS_ARDUINO_EXT_RELEASES

I have found with some slight modifications to the sketch this all works as expected (see screenshot below)