Hello
I had choose avrisp mkii programmer but after compile nothing happen. What I should check?

Note that I correctly use the same programmer in AVR STUDIO 6.

thanks

Visual Studio ultimate 2012
Visual Micro 1.1404.01
***************************************
Compiling 'TEST_TX_CON_VS2012' for 'Arduino Duemilanove w/ ATmega328'
Build folder: S2012/atmega328
Summary: Header=1 Prototypes=4 Imports=2
Additional Defines: VISUALMICRO_COMPILER_VER=1;
Architecture Tools: C:\Program Files\Arduino\hardware\tools\avr\bin\
GCC: 4.3.2
Sketchbook: file:///C:/Users/Administrator/Documents/Arduino
Include Path 'C:\Program Files\Arduino\hardware\arduino\cores\arduino'
Include Path 'C:\Program Files\Arduino\hardware\arduino\variants\standard'
Include Path 'C:\Program Files\Arduino\libraries\Jeelib'
Include Path 'C:\Program Files\Arduino\libraries\Timer1'
Include Path 'C:\Program Files\Arduino\libraries'
Include Path 'C:\Program Files\Arduino\hardware\arduino\libraries'
Include Path 'C:\Users\Administrator\Documents\Arduino\libraries'
C:\Program Files\Arduino\hardware\tools\avr\bin\avr-g++ -c -g -Os -fno-exceptions -ffunction-sections -fdata-sections -Wall -mmcu=atmega328p -DF_CPU=16000000L -MMD -DUSB_VID=null -DUSB_PID=null -DARDUINO=105 -I"C:\Program Files\Arduino\hardware\arduino\cores\arduino" -I"C:\Program Files\Arduino\hardware\arduino\variants\standard" -I"C:\Program Files\Arduino\libraries\Jeelib" -I"C:\Program Files\Arduino\libraries\Timer1" -I"C:\Program Files\Arduino\libraries" -I"C:\Program Files\Arduino\hardware\arduino\libraries" -I"C:\Program Files\Visual Micro\Visual Micro for Arduino\Micro Platforms\default\debuggers" -I"C:\Users\Administrator\Documents\Arduino\libraries" -o tmega328\TEST_TX_CON_VS2012.cpp.o"  tmega328\TEST_TX_CON_VS2012.cpp"  -DVISUALMICRO_COMPILER_VER=1
C:\Program Files\Arduino\hardware\tools\avr\bin\avr-gcc -Os -Wl,--gc-sections -mmcu=atmega328p \atmega328" -o tmega328\TEST_TX_CON_VS2012.elf" tmega328\TEST_TX_CON_VS2012.cpp.o" tmega328\Jeelib\Ports.cpp.o" tmega328\Jeelib\PortsBMP085.cpp.o" tmega328\Jeelib\PortsLCD.cpp.o" tmega328\Jeelib\PortsRF12.cpp.o" tmega328\Jeelib\PortsSHT11.cpp.o" tmega328\Jeelib\RF12.cpp.o" tmega328\Jeelib\RF12sio.cpp.o" tmega328\Jeelib\RF69.cpp.o" tmega328\Jeelib\RF69_compat.cpp.o" tmega328\Timer1\TimerOne.cpp.o" tmega328\core.a" -lm
C:\Program Files\Arduino\hardware\tools\avr\bin\avr-objcopy -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 tmega328\TEST_TX_CON_VS2012.elf" tmega328\TEST_TX_CON_VS2012.eep"
C:\Program Files\Arduino\hardware\tools\avr\bin\avr-objcopy -O ihex -R .eeprom tmega328\TEST_TX_CON_VS2012.elf" tmega328\TEST_TX_CON_VS2012.hex"
Binary sketch size: 4.962 bytes (used 16% of a 30.720 byte maximum) (1,07 secs)
**********************************

Hello
Where I can found Arduino compatible usb driver for AVRISP mkII



***************************************
Uploading to I/O board using 'AVRISP mkII'
Uploader started for board Arduino Duemilanove w/ ATmega328
Uploader sometimes uses programmer name: avrispmkii
Uploader will attempt to use programmer name: avrispmkii
C:\Program Files\Arduino\hardware\tools\avr\bin\avrdude -C"C:\Program Files\Arduino\hardware/tools/avr/etc/avrdude.conf" -v -v -v -v -patmega328p -cstk500v2 -Pusb N_VS2012\atmega328\TEST_TX_CON_VS2012.hex":i
avrdude: Version 5.11, compiled on Sep  2 2011 at 19:38:36
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\Program Files\Arduino\hardware/tools/avr/etc/avrdude.conf"

         Using Port                    : usb
         Using Programmer              : stk500v2
avrdude: usbdev_open(): did not find any USB device "usb"
*****************************************

After install this new AVRISP MKII Arduino driver, can I still use AVRISP MKII in ATMEL STUDIO or one exclude the other?

ps.
while programming the screen blink a little bit

Hi pinkfloyd11,

working with programmers inside AtmelStudio can be a pain if you wish to do it à la Arduino, I can testify. You need to use the libusb-win32 drivers, but each time you plug in the mkII, the Atmel driver gets loaded (jungo or soemthing like this)  .

Search for my post on the subject, I succeeded in replacing the Atmel driver with the correct one.