VS Arduino - Arduino Due + Segger JLink not available

Sep 23^rd, 2026 at 5:31am (UTC)

Before logging an issue, please update to the latest release of Visual Micro from the Downloads Page.

When Logging a Support Issue in the Forum, please ensure you have also:-

Save the new Output to a Text File and....

Support requests without the output above may be impossible to answer, so please help us to help you

VS Arduino › › › Arduino Due + Segger JLink not available

‹ Previous Topic | Next Topic ›

Pages: 1

Arduino Due + Segger JLink not available (Read 3407 times)

Steve Scholl Junior Member Offline Posts: 16 Joined: Jan 29^th, 2020	Arduino Due + Segger JLink not available Jan 29^th, 2020 at 2:45am	Print Post
	Hi, I'm just beginning my foray into gdb debugging with visual micro. I've connected the jlink to the due but I don't see an option to select the jlink in the list of hardware debuggers. There is Manual, Atmel Ice, and Black Magic. I'm using Visual Micro version 1912.28.2 in Visual Studio 2017. Uploading and executing with the due works fine with Debug : Off. Looking for suggestions on how I can proceed. thanks, steve


	IP Logged

Simon@Visual Micro Administrator Offline Posts: 2962 Joined: Feb 13^th, 2019	Re: Arduino Due + Segger JLink not available Reply #1 - Jan 29^th, 2020 at 10:17am	Print Post
	Not all debuggers are available pre-configured by default, and we will add this configuration in an upcoming release. To make this work immediately: Add a Board.txt to the Project (Right Click project > Add > Add Local board.txt) Add the below line to the new board.txt file created Code tools.openocd.debug.args={debug.verbose} -s "{path}/share/openocd/scripts/" -f "interface/jlink.cfg" -c "interface cmsis-dap" -c "set CHIPNAME at91sam3X8E" -c "source [find {openocdscript}]" -c "init; reset halt" If you select the "Atmel ICE" option now, and attach the debugger it should work as expected for debugging (the above config will override the elements we need). NOTE - You will need to install the Additional WinUSB Driver using Zadig for the JLink to connect, and the orientation of the ribbon cable is also important (as shown on the SAM Debugging Page)
	« Last Edit: Jan 29^th, 2020 at 10:25am by Simon@Visual Micro »

	WWW Facebook Twitter YouTube IP Logged

Steve Scholl Junior Member Offline Posts: 16 Joined: Jan 29^th, 2020	Re: Arduino Due + Segger JLink not available Reply #2 - Jan 29^th, 2020 at 4:08pm	Print Post
	Thanks for the quick reply. I will give that a try this evening. I wanted to get clarification on changing the USB driver with Zadig. Do I install a new driver for the JLink or for the Due?


	IP Logged

Simon@Visual Micro Administrator Offline Posts: 2962 Joined: Feb 13^th, 2019	Re: Arduino Due + Segger JLink not available Reply #3 - Jan 29^th, 2020 at 4:14pm	Print Post
	The Zadig tool will replace the driver for the JLink USB Device, so it is accessible from the OpenOCD software we use to connect to it.


	WWW Facebook Twitter YouTube IP Logged

Steve Scholl Junior Member Offline Posts: 16 Joined: Jan 29^th, 2020	Re: Arduino Due + Segger JLink not available Reply #4 - Jan 30^th, 2020 at 5:49am	Print Post
	That did the trick. Thank You!


	IP Logged

Simon@Visual Micro Administrator Offline Posts: 2962 Joined: Feb 13^th, 2019	Re: Arduino Due + Segger JLink not available Reply #5 - Jan 30^th, 2020 at 3:58pm	Print Post
	Glad to help, and this is now available on the drop down menu with the Atmel ICE / Black Magic in the latest release.


	WWW Facebook Twitter YouTube IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›