Hi, news: I have update the Atmel firmware ICA from V1.0 to V1.27 using Atmel Studio 7. The ICE debugger is detect from AS7, but is still do not detect from vMicro, so, I'm waiting for your fix.

Hi!

For me, there's even more confusion now. I'll try to recapitulate my configuration.

I am using vMicro(commercial licence)  installed on MSVisualStudio (I don't use the Arduino IDE)

My goal is to compile and debug with Atmel ICE for Atmel SAM3X8E processors (Arduino DUE board).

To do a test I tried to import a sketch Arduino DUE  in vMicro : OK imported without problems

I tried to compile the skecth: OK without problems

I tried to launch serial debugging (programmig port): OK it works, I can insert breakpoits, etc..

I inserted on USB the debugger Atmel ICE, I launched again the debugger : It does not work, vMicro does not see the ATMEL ICE.

I'm sorry I confused that message. I repeat the only problem I have is only using the Atmel ICE hardware debugger. 

When I use the serial debugger with the programming port of arduino due it works well. I have some questions about these aspects too but they are secondary and I can wait and I'll ask them later.

Now the problem is that the Atmel device does not appear in the list : Uploader -> Programmer . The window is always empty.

Can you help me?
thanks

I have already explained this below. The programmers list is empty because there are no programmers defined for Arduino and your Due board.

The Arduino Due does not come with an ICE programmer definition so we will try to add that for you next week.

Hopefully you end up with an ICE programmer for upload and an ICE debugger.

NOTE: For some Arduino boards: If you use the ICE programmer for upload you will not be able to use Serial/USB for upload unless you understand how to "burn a bootloader". If you do not understand bootloaders then you should NOT attempt to use a programmer for upload.

do you have a forecast of when this change will be ready so that I can synchronize with my work? 

Hi!
Debugger: Atmel ICE
Compiling 'ArduinoDueProject' for 'Arduino Due (Programming Port)'
Program size: 36.312 bytes (used 7% of a 524.288 byte maximum) (0,45 secs)
 
Uploading 'ArduinoDueProject' to 'Arduino Due (Programming Port)' using 'COM6'
Uploader started for board Arduino Due (Programming Port)
Upload method will be: bootloader
Uploading via Bootloader 
Unable to auto-reset: COM6. Check that you have the correct port selected. If it is correct, try pressing the board's reset button after initiating the upload.

no\bossac.exe -i -d --port=COM6 -U false -e -w -b C:\Users\marco\AppData\Local\Temp\VMBuilds\ARDUIN~1\ARDUIN~1\Debug/ARDUIN~1.BIN -R
The uploader process failed
No device found on COM6

My sey-up
On ICE: RED led (ON - Green LED (ON)
TARGET: Arduino board DUE (original)
Atmel ICE debugger

connection between ICE - DUE BOARD
ICE          TARGET
3V3   <-   3V3
TMS  ->   TMS
TCK  ->    TCK
TDO  ->    TDI
TDI   <-    TDO
GND  <-    GND

Do nto work.
thanks

We seem to keep confusing the ICE debug with normal upload. The debug has nothing to do with upload.

The error you see if an upload error, the same one you had few days ago which you resolved.

Can you confirm upload is working okay before trying to debug.

we need the info requested in the yellow box posted at .txt file.

OK send it with build properties and verbose.

I stay on Programming port until new order!!

Hi,

If you look at the top of the new releases section you will see there is an update.

I spoke with the debug team and some boards do not allow serial upload while the hardware debugger is connected.

We are adding ICE and other programmers during the next week so that you can upload with the programmer and then debug. In the meantime you might have to unplug the ICE to allow Serial upload.

To start debug you do not have to click Debug>Start because that also attempts to upload. You can click Debug>Attach which just starts the debugger without upload.