VS Arduino - I can not use breakpoints.

Sep 19^th, 2026 at 12:08am (UTC)

Before logging an issue, please update to the latest release of Visual Micro from the Downloads Page.

When Logging a Support Issue in the Forum, please ensure you have also:-

Save the new Output to a Text File and....

Support requests without the output above may be impossible to answer, so please help us to help you

VS Arduino › › › I can not use breakpoints.

‹ Previous Topic | Next Topic ›

Pages: 1

I can not use breakpoints. (Read 2506 times)

kihara Newbies Offline Posts: 5 Joined: Sep 17^th, 2021	I can not use breakpoints. Sep 21^st, 2021 at 6:29am	Print Post
	Debug: Hardware can not use errors and breakpoints can not be used. I am troubled that some kind of setting is bad. Debug: OFF works properly. Please let me know if there is information that is not enough. Thank you for advice.

	Please Register or Login to the Forum to see File Attachments
	IP Logged

kihara Newbies Offline Posts: 5 Joined: Sep 17^th, 2021	Re: I can not use breakpoints. Reply #1 - Sep 21^st, 2021 at 6:30am	Print Post
	next

	Please Register or Login to the Forum to see File Attachments
	IP Logged

kihara Newbies Offline Posts: 5 Joined: Sep 17^th, 2021	Re: I can not use breakpoints. Reply #2 - Sep 21^st, 2021 at 6:33am	Print Post
	Blink1.ino_DebugOpenOCD.log none separate none adapter speed: 2000 kHz Info : Configured 2 cores esp32 interrupt mask on Error: no device found Error: unable to open ftdi device with vid 0403, pid 6010, description '', serial '' at bus location '*' Warn : Flash driver of esp32.flash does not support free_driver_priv() Warn : Flash driver of irom does not support free_driver_priv() Warn : Flash driver of drom does not support free_driver_priv()

	Please Register or Login to the Forum to see File Attachments
	IP Logged

kihara Newbies Offline Posts: 5 Joined: Sep 17^th, 2021	Re: I can not use breakpoints. Reply #3 - Sep 21^st, 2021 at 6:36am	Print Post
	Output.txt Starting: "C:\ProgramData\vmicro\tools\openocd-espressif-esp32-10.0.1\bin/openocd.exe" -d2 -l /Blink1.ino_DebugOpenOCD.log}" -s s/" -f s/interface/ftdi/esp32_devkitj_v1.cfg" -c "set ESP32_RTOS none" -f s/board/esp-wroom-32.cfg" -c "init; reset halt" Starting: sp32-elf-gcc\1.22.0-97-gc752ad5-5.2.0/bin\xtensa-esp32-elf-gdb.exe" --interpreter=mi -ex "set remote hardware-watchpoint-limit 2" -ex "mon reset halt" -ex "flushregs" -ex "thb app_main" -ex "c" "C:\ProgramData\vmicro\tools\openocd-espressif-esp32-10.0.1\bin/openocd.exe" exited with code 1 (0x1).


	IP Logged

Simon@Visual Micro Administrator Offline Posts: 2962 Joined: Feb 13^th, 2019	Re: I can not use breakpoints. Reply #4 - Sep 21^st, 2021 at 9:23am	Print Post
	Thanks for the report. From the first image, there is only a USB Lead connected to the ESP32 board. Unless you are using a board with an in-built Hardware Debugger (e.g. ESP-WROVER-KIT), then you will need an additional board connected to the ESP, e.g. ESPPROG. All pre-configured debuggers and wiring diagrams can be seen on our GDB and ESP32 Page Alternatively you can use the Serial Debugger with your board, without any additional hardware, as shown on this page.


	WWW Facebook Twitter YouTube IP Logged

kihara Newbies Offline Posts: 5 Joined: Sep 17^th, 2021	Re: I can not use breakpoints. Reply #5 - Sep 22^nd, 2021 at 6:28am	Print Post
	Thank you for your response. Hardware debug was misunderstood simply by connecting one USB code. I study the serial debug tutorial and post an unknown point again. Thank you very much.


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›